After more than 30 years of research improvement and strong market demand

After more than 30 years of research and improvement and strong market demand, corrugated flat sheet presses have made considerable progress. Problems such as unstable feeding, large registration errors, difficulty in tuning, ink scraping and dust, etc. have been greatly improved. The degree of improvement can be analyzed by the following structure of each unit:

(1) Feeding part: The traditional paper feeding unit is a push-back type, which often cannot be fed due to the paperboard bending, and the paper feeding cannot guarantee the positioning of the paperboard and thus cause the registration error. After the improvement, vacuum adsorption is used to assist the small area of ​​the adsorption plate or the roller. Although the above disadvantages can be improved, the large area of ​​the cardboard may still cause deviation due to the insufficient contact area. Aiming at these disadvantages, a large-area adsorption vacuum suction paper feeding system can be developed to completely solve these problems and guarantee the registration accuracy of the leading edge feed.

(b) Paper powder removal device: The problem of paper powder has been plagued with the printing quality of corrugated boxes. The initial solution was to remove them by brushing and vacuuming, but the effect was not obvious. The main reason was that dust often adhered to static electricity and adhered firmly. On the cardboard. Nowadays, the higher printing quality requirements are all equipped with high-voltage discharge dust removal devices, which first remove the static electricity and then vacuum to improve the dust removal effect.

(3) Cardboard transport: In the traditional printing machine, the paperboard transport between the printing units is carried out by pulling the paper ring. The pull paper ring needs to adjust the position according to the width of the paperboard, and the printed part must be avoided to avoid scratching the ink. In addition, the staged transfer action will affect the accuracy of registration due to the different degree of paperboard bending. Therefore, the vacuum adsorption transfer system was developed to transport the paperboard by vacuum adsorption and roller method. The paperboard can be sucked into the machine flatly and transmitted stably in the printing unit, and there is no periodic beating between the units, which greatly improves the accuracy of print registration. And there is no need to adjust the position of the paper puller ring for changing the order.

(4) Printing ink supply system: Due to the successful launch of ceramic anilox rollers, flexo printing machines can now be used with single-disc scrapers, closed slotted scrapers and other systems in addition to traditional rubber ink rollers. In order to adapt to different printing needs different ink amount and network line density, the flexibility of printing unit is very important. Some manufacturers consider the printing unit to be equipped with a rubber ink roller and a closed groove scraper to accommodate full plates and overprints. The French company Martin's rapid replacement of closed slotted blade systems, with different scrapers can also adapt to full version and dot printing. Swiss Bobst company is an electric replacement of ceramic anilox roller device. The arrangement of two to three sets of anilox roller in each printing unit can be completed within one minute. It can be applied to a wider range of printing, full printing and printing. Up to 120L/inch network overprint.

(5) Drying unit: In order to adapt to the increasing trend of carton printing, more and more four-color or more printing units are available. Under this premise, the drying unit is necessary, one can improve the printing quality, and the other can Increase production speed. In addition, during the process of connection, the drying unit can isolate the printing and post-processing (grooving die cutting) process, so as to avoid the dust entering the printing unit and the vibration affects the printing quality. The quantity and configuration of the drying unit depend on the needs and budget.

Bobst's models are designed for multi-color printing and in-line lighting, so hot air drying is configured behind each printing unit, and the last unit is equipped with a UV drying unit to coat UV oil.
The above is only the basic improvement of the corrugated sheetfed printing press, and there are other devices that can be used to further improve the printing quality, such as: independent motors for each unit, ink-moisture monitoring and exclusion of abnormal devices. Carton manufacturers should choose the optimal equipment based on market demand and their own investment budget. It can be foreseen that the trend of multi-color and high-quality printing of cartons is unavoidable.