The quality standard requirements and operating procedures of the hardcover binding process refer to the quality standard requirements and operating procedures of various modeling processes and equipment used on the book block after the book is locked. It includes flattening bundles of books, applying adhesives, drying sub-books, cutting books, picking rounds, ridges, three sticks, shell making, hot stamping, sleeve sweeping, etc., which are divided into three major processes. Quality standard requirements for hardcover binding process The hardcover binding includes three upper orders, namely book block processing, book backing processing and sleeve processing. 1. Hardcover book block processing quality standard requirements (1) Flatten ①Adjust the pressure regulation according to the actual thickness of the book block (one or several) being pressed. ② When flattening, the book block should collide neatly, and there should be no irregular shrinkage, skew and tipping, and it should be laid flat. ③The thickness of the book block after flattening is basically the same and should be stacked neatly, and the four corners will not overflow to ensure that the book block is not deformed. (2) Glue the book for the first time ①Use the correct type of glue, apply thinly and evenly without spilling. ② The first application of glue should ensure the softness and firmness of the round, so that the round will not be scattered after the ridge is raised. (3) Grilled round ①The manual rounding is correct, and the rounding of the machine is adjusted properly. ②The roundness of the round circle is calculated by the thickness of the book block, and the center angle of the arc is between 90 degrees and 130 degrees. ③The rounded book block has the same round shape, skewed or one end is large and one end is small, to ensure that the upper and lower corners of the cut edge are vertical. ④ After the book block is rounded, there is no cracking or wrinkling, and it is firm and flat without rounding. (4) Rising ①The book block is clamped and positioned correctly, the four corners are flat and not skewed, and the exposed part of the book block spine is parallel to the top and bottom. ② The spine is smashed properly with no cracks or wrinkles, and the back of the book is sturdy and firm, keeping the roundness correct. ③The height of the ridge is the same, the thickness of the cardboard is 2.5mm, and the height of the ridge is 3mm, and the height is 4mm. The angle between the protruding part of the spine and the writing is 120 degrees ± 10 degrees (the inclination of the ridge to the surface). (5) Sticky bookmark tape and caulking cloth ①The adhesive used is appropriate, apply evenly without overflowing the incision. ②Label length: 20 ± 10mm longer than the diagonal of the book block. Bookmark bandwidth: 3-4mm for books 32 and below, and 5-7mm for books 16 and above. ③Sticked position: It is located at 10mm from the top of the book back in the middle of the book block. ④ Cloth length: the width of the back of the book (square back) or the arc of the book back is 1mm. ⑤The wiring edge of the plug is exposed on the cutouts at the two ends of the book back. (6) Sticky backing paper ①Adhesive should be properly selected and applied evenly without spilling. ②The length of the back sheet of the book: 4mm shorter than the book block. Width of the back of the book: the width of the back of the book (square back) is 1-2mm longer than the arc length of the book. ③ The width of the two sides of the back sheet of paper after sticking is uniform without skew, sticking flat without wrinkle, and the length is uniform. (7) Sticky paper ①Adhesive is appropriate, apply evenly and uniformly, without overflowing and no flower. ②The length of the paper: 3 ~ 4mm longer than the book block. Paper width: add 5mm glue to the arc length of the two books. ③The paper material is selected correctly. The sticking is not skewed, the sticking is not falling off, and the sticking is flat without wrinkles.
Outdoor Sofas Furniture
Sofas furniture that is three seat seat, you can sit together with your friends or family together, or lie down for a lunch rest. Completely comfortable sofas furniture are perfect fit for arid and coastal climates alike.
· Handwoven premium resin wicker UV resistant
· Rust-resistant powder-coated frames
· Cushions included with 30 density sofa foam
· Versatile tempered glass tables
· Cushions also available with 100% waterproof fabric.
Outdoor Sofas furniture with different style and hand weaving
If you have any questions, please contact with us directly. Outdoor Sofa Furniture are produced
by Golden Eagle Outdoor Furniture With High Quality and Good Appearance. Welcome you can visit our Factory.For any inquiry,Please send mail directly to us.
Aluminum Patio Furniture,Garden Furniture Cushions,Contemporary Outdoor Furniture,Garden Outdoor Furniture PE Wicker Golden Eagle Outdoor Furniture Co., LTD. , https://www.gepatio.com