[ Chinese wardrobe net ] wardrobe products are now a must-have product for every family, not only can play a decorative role, but also can save a lot of family space, maximize the use of the living room area, so it is very important to choose the right rotating wardrobe. Next, Xiaobian will introduce it to everyone. The rotating closet is convenient to use, but the installation and drinking of other wardrobes are slightly different. Let's take a look at the rotating closet installation. Use a pad to place the floor. Start by assembling the wide side panel against the end of the wall and lay the wide side panel on the ground. (Keep a distance of 700mm from the rear wall). First, put the plate of the filled three-in-one rubber plug on the cloth, check the hole spacing and the drawing, and install the three-in-one single-link. First, the solid layer nails on the cork Fixed on the wide side plate, the top handle with the large handle hole facing up, the other solid layers are facing downward, the foot line large handle hole facing inward (the middle solid layer and the L frame height are the same, that is, the bottom plate to the solid layer inner space is 960mm, the field layering plate hole). Put the side panels, nail the cork, and the cork is required to connect the solid layers on both sides. Install the double connecting rod on the second cabinet. Note that the large handle on the double connecting rod can only lock half, that is, 90°. When the two solid layers are fixed to the side plates, tighten the large handles at the same time. Repeat the installation steps for the second cabinet when installing the third cabinet. Second, the nail back plate Place the assembled whole cabinet on the floor of the point cloth, and lay the side panels in the same plane. Use a slider to measure the diagonal size of the cabinet and adjust it to the same level. Start with the first backing plate from the wide measuring board. Note that if there is a solid nail in the middle, draw the center line of the solid layer with a pencil and nail it. nail. Third, the installation of the L frame Use the side plates of the L frame to have a parallel line on the corresponding side plates, then move the center line of the three-in-one rubber particles up by 9 mm, and draw a parallel line on the corresponding bottom plate with the top frame of the L frame. The inner center 9mm draws the center line of three rubber pieces. The hole was drilled with a 10 mm drill bit and the hole depth was 10-20 mm. Install a single pole. After the L frame is installed, nails are fixed on the back plate. Clean up the wardrobe installation debris, one person at the left and right, the wardrobe is slightly inclined backwards, lifted hard, and moved back to the desired position. Be careful not to scratch the floor or the wall. Fourth, install three sections of track The track is placed against the drawer, flushing the drawer floor, and the moving female rail fixing sub-rail screw is mounted on the sub-track vertical eye (this is an adjustable position). The distance between the two drawer panels to the center of the track eye is further increased by 2 mm. The data of the female rails is removed and the transverse line is drawn on the side panel of the cabinet with a 90° angle. The cross-sectional line is the center line of the female rail. . The drawer panel is inserted into the column, so the vertical cut line is drawn from the outer side of the side panel of the cabinet, the female rail is flush with the vertical tangent line, the center eye is flush with the line, and the screw is mounted on the transverse eye of the busbar (adjustable position). After the drawer is installed, the adjustable position is used for debugging, so that the drawer surface is flat and the surrounding gap is even. Finally, the fixing screws are placed on the transverse eye of the sub-track and on the vertical eye of the female rail. And so on to install the next one. In the case of full drawers, the same principle can be installed from bottom to top, and the uppermost drawer can be fixed with a 90° angle. The premise requires that the surface is leveled and the apprentice is uniform. The drawer clearance is 2mm. Fifth, the installation of push-pull mirror The three-section rail is mounted on the push-pull mirror, and the height of the push-pull mirror is generally 1700 mm above the bottom solid layer (customer can request height). The rail transverse line is drawn on the side panel at a height of 90° according to the required height. The parallel distance between the new eyes in the three-section track on the upper line is measured, and accurate data is obtained. The lower track transverse line is drawn on the side plate with a 90° angle. Install the upper and lower mother rails of the push-pull. The mother rail is 5mm away from the backboard and is equipped with a push-pull mirror. The above is a small series to introduce you to the relevant information of the rotating wardrobe, solid layer nails on the cork, nail back board, installation of three sections of rail, push-pull mirror installation and other important steps need to pay attention. Avoid making it difficult to use due to installation problems. If you want to know more information, please continue to pay attention.
Metal lockers, or more specifically cold-rolled steel lockers, are secure storage devices for indoor dry environments. They`re durable, efficient, and economical. Metal Locker Cabinet, Full Locker, Metal Lockers for Sale LUOYANG SHIDIU IMPORT AND EXPORT CO., LTD , https://www.shadow-cabinet.com
Here you will find lockers for school, staff, sports, parcel delivery.
You can choose from single, double and triple tier lockers, as well as box lockers.
Choose from gray, tan, or blue powder-coated for your lockers, or colors per Ral No.
There are combination locks, padlocks, key locks (including cylinder locks) lever or knob locks, electronic key pads, or other electronic or wireless locks to choose.
As a metal storage manufacturer, Shidiu Import & Export Co.,Ltd. are always striving to serve you with the most steady quality and best prices.